0 卖盘信息
您现在的位置: 首页 > 商城快讯 > 热门方案> 健康医疗 > ST STEVAL-IME003V1医疗超声波图像解决方案

ST STEVAL-IME003V1医疗超声波图像解决方案

来源: eccn
2019-05-16
类别:健康医疗
eye 19
文章创建人 拍明芯城

原标题:ST STEVAL-IME003V1医疗超声波图像解决方案

  ST公司的STEVAL-IME003V1是基于四路STHV748高压脉冲发生器的超声波图像演示板,输出波形通过连接示波器探针到BNC就能直接在示波器上显示.16种预置波形能用来在变化的条块下测试高压(HV)脉冲发生器.而STHV748是±90 V 2 A高速脉冲发生器,工作频率高达20MHz,主要用于医疗超声图像,脉冲发生器,NDT超声发送和压电传感器驱动器.本文介绍了STHV748主要特性,典型应用电路以及STEVAL-IME003V1主要特性,框图,电路图,材料清单和PCB元件布局图.

  The STEVAL-IME003V1 demonstration board is designed around the STHV748 4-channel high voltage pulser, a state-of-the-art device designed for ultrasound imaging applications.

  The output waveforms can be displayed directly on an oscilloscope by connecting the scope probe to the relative BNCs. 16 preset waveforms are available to test the HV pulser under varying conditions.

  STHV748 is 5-level, ±90 V, 2 A high speed pulser with four independent channels.This monolithic, high-voltage, high-speed pulser generator features four independent channels. It is designed for medical ultrasound imaging applications, but it can also be used for driving other piezoelectric, capacitive or MEMS based transducers. The STHV748 comprises a controller logic interface circuit, level translators, MOSFET gate drivers, noise blocking diodes, and high-power P-channel and N-channel MOSFETs as the output stage for each channel, clamping-to-ground circuitry, anti-leakage, anti-memory effect block, thermal sensor, and a T/R switch which guarantees an effective decoupling during the transmission phase. Moreover, the STHV748 includes self-biasing and thermal shutdown blocks. Each channel can support up to five active output levels with two half bridges. The output stage of each channel is able to provide ±2 A peak output current. In order to reduce power dissipation during continuous wave mode, a dedicated half bridge is available and the peak current is limited to 0.6 A.

  STHV748主要特性:

  0 to ±90 V output voltage

  Up to 20 MHz operating frequency

  Embedded low-power, floating high-voltage drivers (external voltage rails can be also used)

  Mode operations:

  3/5-levels output waveform

  ±2 A source and sink current

  Down ≤ 20 ps jitter

  Anti-cross conduction function

  Low 2nd harmonic distortion

  Fully integrated clamping-to-ground function

  8 Ω synchronous active clamp

  Anti-leakage on output node

  Dedicated half bridge for continuous wave (CW) operations

  ≤ 0.1 W power consumption

  ±0.6 A source and sink current

  ≤ 10 ps jitter

  Fully integrated T/R switch

  13.5 Ω on resistance

  HV MOS topology to minimize current consumption

  Up to 300 MHz BW

  Receiver multiplexing function

  2.4 V to 3.6 V CMOS logic interface

  Auxiliary integrated circuits

  Noise blocking diodes

  Fully self-biasing architecture

  Anti-memory effect for all internal HV nodes

  Thermal protection

  Standby function

  Latch-up free due to HV SOI technology

  Very few external passive components needed

  STHV748应用:

  ■ Medical ultrasound imaging

  ■ Pulse waveform generator

  ■ NDT ultrasound transmission

  ■ Piezoelectric transducers driver

  图1.STHV748典型应用电路

  图2.STEVAL-IME003V1超声波图像演示板外形图

  STEVAL-IME003V1主要特性:

  ● Based on the STHV748 device for ultrasound imagine applications

  ● 4 monolithic channels, 5 level high voltage pulser

  ● Integrated T/R switch

  ● On-board equivalent piezoelectric load implemented by means of:

  – R/C equivalent network

  – SMD landing areas available for a customized output load

  ● USB interface available to upload customized output waveforms

  ● 4 Mb serial Flash memory available for storing customized waveforms

  ● Memory expansion connector is available to expand serial Flash size

  ● High voltage and low voltage connectors to power the STHV748

  ● 25 LEDs to check the board status and proper operation

  ● Human machine interface to select, start and stop the stored output waveforms

  图3.STEVAL-IME003V1超声波图像演示板框图

  图4.STEVAL-IME003V1超声波图像演示板电路图(1)

  图5.STEVAL-IME003V1超声波图像演示板电路图(2)

  图6.STEVAL-IME003V1超声波图像演示板电路图(3)

  图7.STEVAL-IME003V1超声波图像演示板电路图(4)

  图8.STEVAL-IME003V1超声波图像演示板电路图(5)

  图9.STEVAL-IME003V1超声波图像演示板电路图(6)

  图10.STEVAL-IME003V1超声波图像演示板电路图(7)

  图11.STEVAL-IME003V1超声波图像演示板电路图(8)

  图12.STEVAL-IME003V1超声波图像演示板电路图(9)

  STEVAL-IME003V1超声波图像演示板材料清单(BOM):

  图13.STEVAL-IME003V1板元件布局图(顶层)


责任编辑:HanFeng

【免责声明】

1、本文内容、数据、图表等来源于网络引用或其他公开资料,版权归属原作者、原发表出处。若版权所有方对本文的引用持有异议,请联系拍明芯城(marketing(at)iczoom.com),本方将及时处理。

2、本文的引用仅供读者交流学习使用,不涉及商业目的。

3、本文内容仅代表作者观点,拍明芯城不对内容的准确性、可靠性或完整性提供明示或暗示的保证。读者阅读本文后做出的决定或行为,是基于自主意愿和独立判断做出的,请读者明确相关结果。

4、如需转载本方拥有版权的文章,请联系拍明芯城(marketing(at)iczoom.com)注明“转载原因”。未经允许私自转载拍明芯城将保留追究其法律责任的权利。

拍明芯城拥有对此声明的最终解释权。

下一篇: 已是最后一篇
标签: ST 发生器

相关资讯